Rolith, Inc., a leader in developing advanced nanostructured devices, today announces the successful demonstration of Transparent Metal Grid Electrode technology based on its disruptive nanolithography method (Rolling Mask Lithography – RML TM).
Pleasanton, CA (PRWEB) August 12, 2013
Rolith, Inc., a leader in developing advanced nanostructured devices, today announces the successful demonstration of Transparent Grid Electrode technology based on its disruptive nanolithography method (Rolling Mask Lithography - RML (TM)).
We seen an explosive growth of touch screen displays in consumer electronics market. ITO (Indium Titanium Oxide) material is a standard solution for transparent electrodes so far. Apart from a consideration cost and limited supply of this material, it has additional problems: high reflectance of this material reduces contrast ratio, optical properties degrade rapidly below 50 Ohm / , which limits the size of display produced using ITO without degradation of performance.
The only viable alternative to ITO (and the only solution for large touchscreen displays) is a metal wire grid. The requirement for a metal wire grid to be invisible to the human eye means that width of the wire should be less than 2 micron. Moreover, narrow wires are helpful to fight Moire effects, which are caused by superposition of the metal wire grid and the pixel structure of a display.
Rolith, Inc. has used its proprietary nanolithography technology called Rolling Mask Lithography (RML (TM)) for fabrication of transparent metal wire grid electrodes on large areas of substrate materials. RML is based on near-field continuous optical lithography, which is implemented using cylindrical phase masks.
Transparent metal electrodes on glass substrates were fabricated in the form of sub-micron width nanowires, lithographically placed in a regular 2-dimensional grid pattern with a period of tens of microns, and thickness of a few hundreds of nanometers. Such metal structure is evaluated as completely invisible to the human eye, highly transparent (greater than 94% transmission) with a very low haze (about 2%) and low resistivity (< 14 Ohm / ). This set of parameters places Rolith technology above all major competition for ITO-alternative technologies.
Gen-2 RML tool capable of patterning substrates up to 1 meter long and built earlier this year has been used to demonstrate this technology.
“Rolith has launched Transparent Metal Grid Electrodes application development just few months ago, and we are very excited with the extraordinary results already achieved. We believe RML (TM) technology will enable high quality cost effective touch screen sensors for mobile devices and large format displays, monitors and TVs. Currently Rolith is negotiating partnerships with a few touch screen display manufacturers and we hope to move fast with commercialization of our technology next year. Our roadmap also calls for expansion into OLED lighting and flexible substrates in 2014-2015”, said Dr Boris Kobrin, founder and CEO, Rolith. He adds: “Rolith will be presenting its breakthrough technology at the upcoming International Touch Panel and Optical Film Exhibition (“Touch Taiwan 2013”), booth 126, and Printed Electronics USA 2013, booth AA18”
ABOUT ROLITH, INC:
Rolith, Inc. is developing advanced nanostructured products for consumer electronics, solar and green building markets using a proprietary nanolithography technology. Rolith was formed by Dr. Boris Kobrin, Prof. Mark Brongersma and Julian Zegelman in 2008 and is currently located in Pleasanton, CA. The company holds a comprehensive patent portfolio in the areas of nanolithography, material deposition and etch methods, as well as nanophotonic devices. Rolith’s strategic partners include SUSS MicroTec AG and Asahi Glass Company Ltd. Its current investors are DFJ VTB Capital Aurora, a Draper Fisher Jurvetson affiliate fund managed by VTB Capital and AGC America, Inc., the venture arm of Asahi Glass Group. Reported by PRWeb 4 hours ago.
Pleasanton, CA (PRWEB) August 12, 2013
Rolith, Inc., a leader in developing advanced nanostructured devices, today announces the successful demonstration of Transparent Grid Electrode technology based on its disruptive nanolithography method (Rolling Mask Lithography - RML (TM)).
We seen an explosive growth of touch screen displays in consumer electronics market. ITO (Indium Titanium Oxide) material is a standard solution for transparent electrodes so far. Apart from a consideration cost and limited supply of this material, it has additional problems: high reflectance of this material reduces contrast ratio, optical properties degrade rapidly below 50 Ohm / , which limits the size of display produced using ITO without degradation of performance.
The only viable alternative to ITO (and the only solution for large touchscreen displays) is a metal wire grid. The requirement for a metal wire grid to be invisible to the human eye means that width of the wire should be less than 2 micron. Moreover, narrow wires are helpful to fight Moire effects, which are caused by superposition of the metal wire grid and the pixel structure of a display.
Rolith, Inc. has used its proprietary nanolithography technology called Rolling Mask Lithography (RML (TM)) for fabrication of transparent metal wire grid electrodes on large areas of substrate materials. RML is based on near-field continuous optical lithography, which is implemented using cylindrical phase masks.
Transparent metal electrodes on glass substrates were fabricated in the form of sub-micron width nanowires, lithographically placed in a regular 2-dimensional grid pattern with a period of tens of microns, and thickness of a few hundreds of nanometers. Such metal structure is evaluated as completely invisible to the human eye, highly transparent (greater than 94% transmission) with a very low haze (about 2%) and low resistivity (< 14 Ohm / ). This set of parameters places Rolith technology above all major competition for ITO-alternative technologies.
Gen-2 RML tool capable of patterning substrates up to 1 meter long and built earlier this year has been used to demonstrate this technology.
“Rolith has launched Transparent Metal Grid Electrodes application development just few months ago, and we are very excited with the extraordinary results already achieved. We believe RML (TM) technology will enable high quality cost effective touch screen sensors for mobile devices and large format displays, monitors and TVs. Currently Rolith is negotiating partnerships with a few touch screen display manufacturers and we hope to move fast with commercialization of our technology next year. Our roadmap also calls for expansion into OLED lighting and flexible substrates in 2014-2015”, said Dr Boris Kobrin, founder and CEO, Rolith. He adds: “Rolith will be presenting its breakthrough technology at the upcoming International Touch Panel and Optical Film Exhibition (“Touch Taiwan 2013”), booth 126, and Printed Electronics USA 2013, booth AA18”
ABOUT ROLITH, INC:
Rolith, Inc. is developing advanced nanostructured products for consumer electronics, solar and green building markets using a proprietary nanolithography technology. Rolith was formed by Dr. Boris Kobrin, Prof. Mark Brongersma and Julian Zegelman in 2008 and is currently located in Pleasanton, CA. The company holds a comprehensive patent portfolio in the areas of nanolithography, material deposition and etch methods, as well as nanophotonic devices. Rolith’s strategic partners include SUSS MicroTec AG and Asahi Glass Company Ltd. Its current investors are DFJ VTB Capital Aurora, a Draper Fisher Jurvetson affiliate fund managed by VTB Capital and AGC America, Inc., the venture arm of Asahi Glass Group. Reported by PRWeb 4 hours ago.